Invisible Zipper Foot Husqvarna - 920458096

An invisible zipper is always inserted before stitching the garments seam. The Invisible Zipper Foot has two grooves underneath the foot to accommodate the zipper coils and hold them in place as you stitch. Buy a zipper that is at least 1 1/4" (3 cm) longer than the zipper opening.

An invisible zipper is always inserted before stitching the garments seam. The Invisible Zipper Foot has two grooves underneath the foot to accommodate the zipper coils and hold them in place as you stitch. Buy a zipper that is at least 1 1/4" (3 cm) longer than the zipper opening.

1. Mark the length of the zipper opening on the seam allowance and on the zipper. The excess length should be at the bottom of the zipper.
2. Snap on the Invisible Zipper Foot. Select center needle position straight stitch. Length 2.5 - 3.0.
3. Unzip the zipper.
4. Place the right part of the zipper on the fabric right sides together. The coil should be on the seamline and the top stop of the zipper 3/4" (2 cm) below the cut edge of the fabric. (Illustration A)
5. Finger press up the zipper coils and lower the presser foot with the zipper coils in the right opening under the foot. 
6. Adjust needle position to align the needle with the needle guide on the front of the foot. Backstitch and sew. Stop at the mark on the zipper and seam allowance and backstitch to tie off. 
7. Place the left part of the zipper right sides together with the left side of the garment. Lower the presser foot with the left opening over the zipper teeth. Make sure that the needle is perfectly aligned with the needle guide in front of the foot again. Sew in the same way as the first side.
8. Pull up the zipper pull. Place the fabric with the zipper right sides together. Snap on the regular Zipper Foot to the left of the needle. Adjust needle position to the right. Start stitching in the backstitched seam and sew the seam below the zipper.

If the zipper is too long, whipstitch across the zipper teeth 1 1/4" (3 cm) below the inserted zipper length. Cut away excess zipper below the whipstitching.

Compatible Machines

• Group 1 - Orchidea, 1250, #1+, 1200, 1100, 1090, 1070, 1070 S, 1050
• Group 2 - Prisma, 990 S, 990, 980, 960, 950 S, 950, 945, 940
• Group 3 - Optima, 630, 620, 610, 190, 185, 180, 150, 120
  
• Group 4 - Classica, 105, 100, 95, 90
• Group 5 - Daisy, Prelude 360, Prelude 340, Daisy 335, Daisy 330, Daisy 325, Daisy 320, Daisy 315, Daisy 310, Husqvarna Viking 250, Husqvarna Viking 230, Husqvarna Viking 225/215, Husqvarna Viking 210, Husqvarna Viking 205, Scandinavia 100, Eden Rose 250M, Tribute 140M, Emerald 122, Emerald 118, Emerald 116
• Group 6 - Platinum 955 E, Platinum 950 E, Platinum Plus 775, 770, 755 Quilt, 750 Quilt, 735, 730, 715, 535, Rose 605, 600, Iris, Lily 555, 550, 545, 540, 530, Husqvarna Viking 500, Interlude 445, 435, Freesia 425, Freesia 415, Husqvarna Viking 400, 350, Scandinavia 400, 300, 200, Emerald 203, 183, Designer Jade 35, Jade 20, Opal 650, 670
• Group 7 - Designer Diamond Royale, Designer Diamond deLuxe, Designer Diamond, Designer Ruby deLuxe, Designer Ruby, Designer Ruby Royale, Designer Topaz 50, Designer Topaz 30, Designer Topaz 20, Designer Topaz 25, Designer Topaz 40, Designer SE, Designer SE Limited Edition, Designer I, Designer II, Quilt Designer, Quilt Designer II, Sapphire 960Q, Sapphire 965Q, Sapphire 85, 930, 875Q, 870Q, 855, 850, 835, 830, Designer Brilliance 80, Designer Brilliance 75Q, Designer Brilliance 80, Opal 690Q, Opal 670, 650, Eden Rose 250C, Tribute 140C
• Designer Epic
• Epic 95Q
• 980Q
• Designer Epic 2